Fitter Objective Question with Answers pdf [free Download ] MCQ

Fitter objective question with answers pdf

Fitter objective question with answers pdf

Fitter objective question with answers pdf

Basic Fitting

76- What is the name of V block? | इस V ब्लॉक का नाम क्या है ?

(a) V grooved V block | V ग्रूवेड V ब्लॉक
(b) Single level single groove V block | सिंगल लेवल सिंगल ग्रूव V ब्लॉक
(c) Double level single groove V block | डबल लेवल सिंगल ग्रूव V ब्लॉक
(d) Single level double groove V block | सिंगल लेवल डबल ग्रूव V ब्लॉक

Answer – b

77- What is the name of the part marked as x in combination set? | संयोजन सेट (कॉम्बिनेशन सेट) में x के रूप में चिह्नित भाग का नाम क्या है ?

(a) Rule | रूल
(b) Scriber | स्क्राइबर
(c) Clamp nut | क्लैंप नट
(d) Spirit level | स्पिरिट लेवल

Answer – b

78- Which caliper is used to find the centre of round bars? | राउंड बार के केंद्र को खोजने के लिए किस कैलीपर का उपयोग किया जाता है ?
(a) Inside caliper | इनसाइड कैलिपर
(b) Jenny caliper | जेनी कैलिपर
(c) Vernier caliper | वर्नियर कैलीपर्स
(d) Outside caliper | आउटसाइड कैलिपर

Answer – b

79- What is the name of angle marked a in chisel? | छेनी मे a से चिह्नित कोण का नाम क्या है ?

(a) Rake angle | रेक कोण
(b) Wedge angle | वैज कोण
(c) Cutting angle | कटिंग एंगल
(d) Clearance angle | निकासी कोण (क्लीयरेंस कोण)

Answer – d

80- Which chisel is used for cutting curved grooves? | घुमावदार ग्रुवेस को काटने के लिए किस छेनी का उपयोग किया जाता है ?
(a) Flat chisel | फ्लैट छेनी
(b) Web chisel | वेब छेनी
(c) Cross cut chisel | क्रॉस कट छेनी
(d) Half round nose chisel | हाफ राउंड नोज छेनी

Answer – d

81- What is the weight of hammer used for marking purpose? | मार्किंग उद्देश्य के लिए उपयोग किए जाने वाले हथौड़ा का वजन क्या है ?
(a) 200 grams | 200 ग्राम
(b) 250 grams | 250 ग्राम
(c) 300 grams | 300 ग्राम
(d) 450 grams | 450 ग्राम

Answer – b

82- What is the effect of improper method of diagonal filing? | विकर्ण फाइलिंग के अनुचित तरीके का प्रभाव क्या है?
(a) Uneven surface finish | असमान फिनिश सतह
(b) Scratches on the surface | सतह पर खरोंच
(c) Convexity on the surface | सतह पर उत्तलता
(d) Improper finish on surface | सतह पर सही फिनिश न होना

Answer – a

83- Which chisel is used to remove excess metal from welded joint and castings? | वेल्डेड जॉइंट और कास्टिंग से अतिरिक्त धातु को हटाने के लिए किस छेनी का उपयोग किया जाता है ?
(a) Flat chisel | फ्लैट छेनी
(b) Web chisel | वेब छेनी
(c) Cross cut chisel | क्रॉस कट छेनी
(d) Half round chisel | हाफ राउंड छेना

Answer – a

84- What is the name of file ? | इस फ़ाइल का नाम क्या है?

iti tool emage

(a) Rotary file | रोटरी फ़ाइल
(b) Tinkers file | टिंकर फाइल
(c) Barrette file | बैरेट फ़ाइल
(d) Crossing file | क्रासिंग फाइल

Answer – a

85- Why chalk is applied on the face of the file? | फ़ाइल के फेस पर चॉक क्यों लगाया जाता है ?
(a) To reduce excessive pressure | अत्यधिक दबाव को कम करने के लिए
(b) To increase chip removed rate | चिप हटाने की दर को बढ़ाने के लिए
(c) To reduce penetration and pinning | पेनिट्रेशन और पिनिंग को कम करने के लिए
(d) To increase penetration and pinning | पेनिट्रेशन और पिनिंग को बढ़ाने के लिए

Answer – c

86- What is the use of fine pitch hacksaw blades? | फाइन पिच हैकसॉ ब्लेड का उपयोग क्या है ?
(a) To cut soft metal | मुलायम धातु को काटने के लिए
(b) To cut high speed steel | हाई स्पीड स्टील को काटने के लिए
(c) To cut high carbon steel | हाई कार्बन स्टील को काटने के लिए
(d) To cut conduit and other thin tubes | कान्ड्रइट और अन्य पतली ट्यूबों को काटने के लिए

Answer – d

87- Calculate the tap drill size for M10 x 1.25. | M10 × 1.25 के लिए टैप ड्रिल साइज़ की गणना करें।
(a) 8.8mm
(b) 8.7mm
(c) 8.75mm
(d) 8.65mm

Answer – a

88- What is the name of portion left between flutes in a drill? | एक ड्रिल में फ्लूटेस के बीच के भाग का नाम क्या है?
(a) ALip | लिप
(b) Web | वेब
(c) Point | पॉइंट
(d) Shank | शेंक

Answer – b

89- What is the reading of vernier bevel protractor? | इस वर्नियर बेवल प्रोट्रैक्टर की रीडिंग क्या है?

(a) 27°30′
(b) 67° 30′
(c) 157° 30′
(d) 159° 30′

Answer – c

90- Which part of outside micrometer ensure a uniform pressure between the measuring surface? | बाहरी माइक्रोमीटर का कौन सा भाग मापने की सतह के बीच एक समान दबाव सुनिश्चित करता है?
(a) Anvil | निहाई
(b) Thimble | नोक
(c) Spindle lock | स्पिंडल लॉक
(d) Ratchet stop | रचेट स्टॉप

Answer – d

<<< Previous Next >>>

Leave a Comment