Mechanic Tractor 1st sem nimi question paper | ITI Question Bank | Home
Mechanic Tractor 1st semester MCQ
ITI Question Bank
Mechanic Tractor Objective Question & Answer:-
1- How the size of the bench vice is referred to?
(a) Width of the jaw
(b) Depth of the jaw
(c) Length of the movable jaw
(d) Length of the fixed jaw
Answer – a
2- What is the name of the part marked as X?
(a) Beam
(b) FiXed jaw
(c) Vernier scale
(d) Depth-measuring blade
Answer – d
3- What is the name of the part marked as X?
(a) Cap
(b) Lock
(c) Stock
(d) Graduated sleeve
Answer – b
4- What is the least count of the outside metric micrometer?
(a) 0.01 mm
(b) 0.10 mm
(c) 0.0001 mm
(d) 0.00001 mm
Answer – a
5- What is the fixed measuring face of a micrometer?
(a) Anvil
(b) Barrel
(c) Spindle
(d) Thimble
Answer – a
6- Which material is used in the outside micometer anvil?
(a) Brass
(b) Bronze
(c) Carbon
(d) Carbide
Answer – d
7- What is the name of the part marked as X?
(a) Anvil
(b) Frame
(c) Spindle
(d) Thimble
Answer – a
8- What is the value of one thimble division reading in an outside micrometer?
(a) 0.05 mm
(b) 0.01 mm
(c) 0.02 mm
(d) 0.03 mm
Answer – b
9- What is the name of the measuring instrument?
(a) Depth gauge
(b) Bore dial gauge
(c) Telescopic gauge
(d) Vernier gauge
Answer – b
10- What is the name of the part marked as X?
(a) Spindle
(b) Plunger
(c) FiXed Anvil Insert
(d) Centering shoes
Answer – b
11- Which instrument is used to read the telescopic gauge measurement?
(a) Depth micrometer
(b) Inside micrometer
(c) Outside micrometer
(d) Three-point internal micrometer
Answer – c
12- What is the name of the part marked as X?
(a) Anvil
(b) Clamp
(c) Plunger
(d) Stem
Answer – b
13- What is the name of the gauge?
(a) Feeler gauge
(b) Snap gauge
(c) Telescopic gauge
(d) Plug gauge
Answer – a
14- Which instrument is used to check the endplay of the crankshaft?
(a) Dial test indicator
(b) Telescopic gauge
(c) Bore dial gauge
(d) Slip gauge
Answer – a
15- Which can be measured by a feeler gauge?
(a) Radius
(b) Screw pitch
(c) Surface roughness
(d) Gap between mating parts
Answer – d
16- Which marking media was used to mark the finished surfaces?
(a) Whitewash
(b) Prussian blue
(c) Copper Sulphate
(d) Cellulose lacquer
Answer – b
17- Which marking media is used on the rough surfaces?
(a) Whitewash
(b) Prussian blue
(c) Copper Sulphate
(d) Cellulose lacquer
Answer – a
18- Which marking media is poisonous?
(a) Whitewash
(b) Prussian blue
(c) Copper Sulphate
(d) Cellulose lacquer
Answer – c
19- What is the name of the equipment?
(a) Surface plate
(b) Angle plate
(c) V Block
(d) Parallel Block
Answer – a
20- Which instrument is used to check the right angle?
(a) Steel rule
(b) Try square
(c) Firm joint caliper
(d) Spring joint caliper
Answer – b
21- What is the use of an outside caliper?
(a) Check the flatness
(b) Check the angle
(c) Check the internal dia of the job
(d) Check the external dia of the job
Answer – d
22- Which hammer is used for general, riveting, and gasket cutting?
(a) Lead hammer
(b) Claw hammer
(c) Plastic hammer
(d) Ball pein hammer
Answer – d
23- Which wrench is used to measure the twisting force?
(a) Torque wrench
(b) Still son pipe wrench
(c) Footprint pipe wrench
(d) HeXagonal socket wrench
Answer – a
24- Which vice is used to grip small screws, rivets, and keys?
(a) Pipe vice
(b) Hand vice
(c) Pin vice
(d) Toolmaker s vice
Answer – b
25- What is the use of C clamp?
(a) Hold the work
(b) Hold the tool
(c) Hold the work table
(d) Support the tool
Answer – a
Mechanic Tractor 1st sem nimi question paper