ITI Fitter MCQ Important Question Answer in English NCVT & SCVT
ITI Fitter MCQ Important Question Answer in English: iti fitter mcq questions, fitter shop 1000 questions-answers pdf download,iti fitter chapter wise mcq fitter mcq book pdf, iti fitter mcq 1st year, iti fitter mcq pdf, nimi fitter mcq pdf, iti fitter mcq pdf download in english
Objective Question and Answers:-
Q 1. In the outside micrometer, datum lines and graduations are marked on
Q 2. The two parts of a try square are . . .
(a) Straight and blade
(b) Stick and plate
(c) Stock and blade
(d) Stock and wedge
Q 3. A micrometer has a negative error of 0.03 mm. What is the correct reading if the micrometer measures 40.53 mm?
(a) 40.50 mm
(b) 40.56 mm
(c) 40.46 mm
(d) 40.59 mm
Q 4. Kerosene oil is used as a coolant while drilling a workpiece made of…
(d) Wrought iron
Q 5. Which one of these bonds is most commonly used on grinding wheels?
Q 6. In the figure given below, which one is …….. hammer?
(a) cross peen hammer
(b) ball peen hammer
(d) claw hammer
Q 7. For general purposes, a bench vice is fixed at a height of…
(a) 80 cm
(b) 90 cm
(c) 106 cm
(a) 125 cm
Q 8. Identify the machine shown in the figure given below.
(d) Milling machine
Q 9. The bed of a lathe is made of ……………….
(a) Alloy steel
(b) Mild steel
(c) Cast iron
(d) Wrought iron
Q 10. Which of these is NOT a part of the center- lathe?
(b) Feed rod
(d) Lead screw
Q 11. In the figure given below, identify the lathe operation being done.
(d) Pattern making
Q 12. Which among these metals is the lightest?
Q 13. Identify the gauge shown in the figure given below.
(a) Standard gauge
(b) Wire gauge
(c) Depth gauge
(d) Drill gauge
Q 14. Which of these is an example of a semi-liquid lubricant?
(c) Lard oil
(d) Castor oil
Q 15. The most common cutting fluid used in almost all machining operations is……
(a) Soluble oil
(c) Compressed air
Q 16. Which of these cutting tools is used to finish and enlarge a hole?
(d) Boring bar
Q 17. The process of beveling the end of an existing drilled hole is called..
Q 18. The figure given below shows a type of cut of a file. What is it?
(a) Single cut
(b) Double cut
(c) Curved cut
(d) Rasp cut
Q 19. The teeth of the hacksaw blade are bent as shown below. It is called…
Q 20. It is a type of paper that can be used for sanding down hard and rough surfaces. It is called
(a) Rigid paper
(b) Tough paper
(c) Hard paper
(d) Emery paper
Q 22. Which one of these is NOT a type of oxy-acetylene flame?
(a) Neutral flame
(b) Natural flame
(c) Oxidising flame
(d) Carburizing flame
Q 23. The drilled hole is larger than the size of the drill used. It could be due to
(a) Too much feed
(b) Helix angle not accurate
(c) Lip clearance not accurate
(d) Unequal length of the cutting edges
Q 24. If a bench vice is over-tightened, what is likely to be damaged?
(c) Square nut
(d) Fixed jaw
Q 25. Which of these is not a base unit under SI system of units?
Q 26. The main purpose of the heat treatment process “normalizing” is…..
(a) Remove induced stresses
(b) Improve machinability
(c) Soften steel
(d) Increase toughness and reduce brittleness
इसे भी पढ़े